Skip to main content

Picoflyer - Worlds Smallest RC Helicopter

By
I found this while searching about helicopters.

Picoflyer


Petter Muren, a Norwegian engineer has invented world's smallest RC helicopter. With just a rotor diameter of 60mm and a weight of just 3.3 grams, the Picoflyer can take off from the palm of your hand.

While normal RC helicopters rely on gyros or sophisticated autopilot systems for stability, the Picoflyer uses a unique stability system (invented and patented also by Petter Muren). The Picoflyer relies on a passive-stability system that naturally tilts the ringed rotors to keeps the heli stable if it starts to lean one way. This new system adds no extra parts or weight to the heli.

parts of the Picoflyer

While intended to be a one-off prototype, the military, universities and hobby manufacturers have expressed their interest to it. The passive-stability system has already inspired a larger commercial RC helicopter named Bladerunner.

The Bladerunner


References 
http://www.popsci.com/diy/article/2006-03/you-built-what-tiny-helicopter
http://www.proxflyer.com/pi_meny.htm
Labels:

Comments

  1. HealthcoachFebruary 10, 2011 at 1:00 PM

    Thank you for taking to time to prepare such an informative and enlightening post.
    Thanks.

    Healthcoach here

    ReplyDelete

Post a Comment

Popular posts from this blog

Selecting the Correct Gauge Wires for your RC Models

By
When we are building RC models (aircrafts, multicopters etc.), something we typically overlook is what type of wires to use to distribute power in them. Usually, we try to reduce the weight of the model, so we tend to go with smaller wires. But, we cant expect to put in small circuit-wires and have them handle the amount of power needed. If you look at the wires that comes in the output leads of a Li-Po, or the wires that comes on a standard XT Jack, you'll notice that they're quite huge. Large gauge wires on a Li-Po and XT connectors These need to be huge to handle the amount of amperage that goes through them. So, we should also consider the amperage, and the length of wire needed when selecting the size (gauge) of the wires.
Post a Comment
Read more

What do the prop size numbers mean?

By
Have you been trying to shop for propellers - either online or at a hobby shop - and got confused of the numbering used to denote the size of the propellers? You see things like " 10 x 4.5 CW ", or " 8055 CCW ". What do these numbers mean? A 8 x 4.5 CW and CCW Propeller Set It's actually quite simple once you figure it out. The first number denotes the diameter of the prop (length from tip-to-tip). The second number denotes the pitch of the prop. Here, the pitch is denoted as a length, not a angle. Let's see how that works.
1 comment
Read more

RC Helicopter Gyro Explained

By
I recently bought a RC Helicopter - a Falcon 8911 4-Channel  RC with a built-in Gyroscope (Gyro for short). It's the first time I've seen a 4-Channel RC helicopter, let alone a one with a gyro, in the Sri Lankan market. The heli was pretty good, although I still need more 'flight training'. I will do a separate post on my heli ;) The thing that interested me most is the gyroscope. I knew the basic concept of a gyroscope but didn't know how it applied to helicopters. So I did a little research on the internet and found out a lot about gyros. To others who are interested, here's what I've learned. First of all, what is a gyro? A gyroscope is a device for measuring or maintaining orientation (a.k.a. angular position). The most basic is the mechanical gyro. A mechanical gyro is essentially a wheel spinning at a high rated speed and whose axle is free to take any orientation. Based on the principles of conservation of angular momentum, the orientation of
3 comments
Read more